Cheap Diesel Engine Driven High Suction Trash Pump

Self-priming pumps are a specific type of liquid pump designed to have the required liquid inside the cavity or pump body necessary to start the pumping process. This offers the potential for increased operating efficiencies in process plants where pumps are used for a variety of repeated yet intermittent operations.
If a pump is located beneath the level of the liquid to be pumped, gravity and air pressure ensure that it is constantly filled with the liquid and there can be no ingress of air into the pump or suction line.
 

In many applications, a pump has to be placed above the level of the liquid, for example, when emptying an underground storage tank. At start-up, there will be air in the suction line and before the pump can discharge the liquid, this air must be evacuated or displaced. Pumps are optimized to move a particular liquid; evacuating a gas is a very different challenge.
Various methods can be used to get around this problem. A secondary pump can be used to evacuate the suction line. A non-return (foot) valve or evacuation tank can be used to stop fluid draining from the suction line when the pump is stopped.
However, these solutions all involve extra equipment, piping, and processes. Ideally, for these applications, a pump is required that can evacuate air from the suction side at startup before commencing its normal pumping mode. Such a pump is considered to be self-priming.

1. What's the advantages Of Self-Priming Centrifugal Pumps?
a. Can handle a variety of liquids.
b. Work well with slurries, corrosive liquids, and suspended solids.
c. When compared to submersible-type pumps, self-priming centrifugal pumps will continue to pump liquids even after the pump is no longer submerged in a liquid tank or vessel.
d. Ideal for frequent and intermittent pumping operations, as the steps involving pump priming on start-up are eliminated.

2. What's the disadvantages Of Self-Priming Centrifugal Pumps?
a. Can't operate without the presence of the initial priming liquid in the pump's reservoir.
b. Due to the need for a liquid reservoir, this type of centrifugal pump can be larger than a standard model, which may cause issues in applications where space is limited.
c. Need to be as close as possible to production lines to avoid depletion of the pump's liquid reservoir during self-priming operations.

3. Are Positive Displacement Pumps Self-Priming?
In principle, all positive displacement pumps are self-priming. In particular, this includes rotary gear pumps (internal and external), lobe pumps, vane pumps, and diaphragm pumps. A common feature of all positive displacement pumps is the use of close-tolerance parts to prevent fluid from returning from the discharge to the suction side.
Depending on the effectiveness of these seals created by these close-tolerance parts, a positive displacement pump is capable of venting air from its suction line to some extent. However, under dry running conditions, a pump may overheat and this can cause seal wear and pump failure.
With reciprocating pumps, there is also a danger of cavitation occurring at the point when liquid starts to enter the pump and there is a liquid/air mixture. Under these conditions, vapor bubbles form and expand on the suction side of the pump. Upon reaching the high pressure, discharge side of the pump, the bubbles collapse violently causing vibration and damage to the pumping elements.
For these reasons, it is important to refer to the manufacturer before using a positive displacement pump in an application where it must self-prime and, of necessity, be run dry for any period.

4. Are Centrifugal Pumps Self-Priming?
With centrifugal pumps, the pumping action is generated by the transfer of rotational energy from the impeller to the liquid. There are no seals between the suction and discharge sides of the pump. This means that centrifugal pumps are ineffective with gases and are not capable of evacuating air from a suction line when the liquid level is below that of the impeller.
In such cases, the pump is said to be air-bound and there is a danger of overheating: generally, pumps rely on the pumped fluid to lubricate and cool the pump's bearings.
However, with a few modifications to the basic design, a centrifugal pump can be self-priming. The impeller and volute casing is essentially surrounded by a tank so that it can always be immersed in a liquid sufficient to get the pump started and provide the pump with lubrication and cooling provided the time is taken to prime the pump is not excessive.
It is important that a self-priming centrifugal pumps reservoir is filled correctly with liquid after installation. "Self-priming" in this context means that the pump has the ability to use liquid stored in its housing to generate a vacuum on the suction line. Even a 'self-priming' centrifugal pump will not operate when dry. With appropriate bearings and seals, a centrifugal pump can tolerate dry running for a limited time but this is not recommended for extended periods.

5. Why Your Self-Priming Pump Won't Prime?
a. Air Leak In Suction Line
As fluid recirculates in the pump and forces air out of the discharge chamber, it's trying to create an area of low pressure. However, if there's a leak in the suction line, air continues to be drawn into the pump, never allowing it to release enough to create that area of low pressure.
b. Debris In The Impeller
If the eye of the impeller is plugged with debris, it removes the hydraulic capacity of the impeller to create an area of low pressure.
c. Pump Is Air Bound
A pump can become air-bound if it experiences any of these conditions:
No Air Release Line. If there is no air release line, air cannot be vented to the atmosphere, and instead collects on the discharge side.
Discharge Line Is Pressurized. Valve on the air release line is closed, and the valve on the discharge line is closed, again, giving no place for the air to go and get out of the pump.
Excessive Impeller Clearance. If there is excessive clearance between the impeller and the wear plate, the pump has a difficult time creating a low-pressure area. This is typically caused by wear, but could also be due to improper reassembly.
d. Plugged Recirculation Port
During the priming process, as discussed above, fluid is recirculated through the volute casing. If the recirculation port becomes plugged, the eye of the impeller is unable to create an area of low pressure in which to pull liquid up the suction line.
e. Lift Too High For Pump Speed Or Impeller Diameter
If you've undersized the pump for the suction line, it will not be able to create the low-pressure area it needs to prime. It's important to understand the suction lift requirements before selecting a pump for the application. Use Gorman-Rupp's Pump Selection Guide for the calculations you'll need. 
The ability for self-priming pumps to prime hinges on all the right conditions. The pump must be able to evacuate air from inside the pump, create a low-pressure area at the eye of the impeller, and also be properly sized for the right NPSH conditions.